CBR3006I states
The system programmer and/or system operator should verify each of the following
items:
Verify that each of the tape subsystem control units within the tape library
is powered on and correctly IML'ed.
Verify that the channel interfaces from each tape subsystem control unit to
the channel subsystem of the processor complex on which this message (CBR3006I)
was received are enabled.
Verify that the channel paths to each tape device within the tape library
are online using the MVST DEVSERV PATHS command.
Verify that the tape devices within the tape library are online using both
the MVS DISPLAY UNITS command and the MVS LIBRARY DISPDRV command.
Verify that the Library ID that appears in the text of this message matches
the library sequence number that is displayed at the library. The library
sequence number is set by the IBMR customer engineer when the tape library is
installed or when a teach operation is performed at the Library Manager service
console.
If the Library ID in this message does not match the library sequence number
displayed at the library, then correct whichever one is wrong (the two must be
the same).
If the Library ID in message CBR3006I is wrong, alter the Library ID using
the ISMF ALTER line operator on the ISMF Tape Library List panels and
re-activate the SMS configuration using the SETSMS command or the ISMF Control
Data Set Application. After reactivating the SMS configuration, verify the tape
library is online by issuing the following command:
DISPLAY SMS,LIBRARY(library-name),DETAIL
If the tape library is not online, vary the tape library online by issuing
the following command:
VARY SMS,LIBRARY(library-name),ONLINE
If the library sequence number at the library is wrong, have your IBM
customer engineer correct the library sequence number, and either re-IPL the MVS
operating system or reactivate the IODF containing the drive definitions.
If the Library ID that appears in the text of this message matches the
library sequence number that is displayed at the library, and the library was
defined to HCD using the optional LIBRARY-ID and LIBPORT-ID parameters, when the
tape library and library devices are available to the system, vary at least one
of the library devices online using the MVS VARY command and then vary the tape
library online by issuing the following command:
VARY SMS,LIBRARY(library-name),ONLINE
Verify that the drives in the library are not defined to HCD with LIBRARY=NO
specified. Though it is not required, in case the drives are not available at
IPL or when the IODF is activated, it is recommended that the drives in the
library be defined to HCD with LIBRARY=YES and the optional LIBRARY-ID and
LIBPORT-ID parameters specified.
Lizette
-----Original Message-----
Behalf Of Crabtree, Anne D
Sent: Sunday, December 04, 2016 6:27 PM
Subject: Re: 3957-VEA TS7720 power outage
Here's what OAM is telling me
CBR0001I OAM initialization starting.
CBR0119I Entry default data class for library WVCHAS not available.
CBR0119I Entry default data class for library WVFLAT not available.
CBR3006I Library WVCHAS with Library ID D7720 unknown in I/O configuration.
CBR3002E Library WVCHAS no longer usable.
CBR3006I Library WVFLAT with Library ID D7740 unknown in I/O configuration.
CBR3002E Library WVFLAT no longer usable.
CBR3006I Library WV7700 with Library ID C0001 unknown in I/O configuration.
CBR3002E Library WV7700 no longer usable.
CBR3911I There is no online and operational tape library.
There are two ficon connections and they are currently online. I have tried
varying them off and back on... multiple times.
IEE174I 20.26.00 DISPLAY M 014
CHPID 42: TYPE=1D, DESC=FICON INCOMPLETE, ONLINE
DEVICE STATUS FOR CHANNEL PATH 42
0 1 2 3 4 5 6 7 8 9 A B C D E F
SWITCH DEVICE NUMBER = NONE
ATTACHED ND = NOT KNOWN
PHYSICAL CHANNEL ID = 0118
************************ SYMBOL EXPLANATIONS ************************
* PHYSICALLY ONLINE $ PATH NOT OPERATIONAL
Anne D. Crabtree
System Programmer
WV Office of Technology Data Center
1900 Kanawha Blvd East
Bldg 6, Room B-110
Charleston, WV 25305
(304)957-8292
(304)558-1441 fax
Work Hours: 6AM-2PM EST
-----Original Message-----
Behalf Of Lizette Koehler
Sent: Sunday, December 04, 2016 8:15 PM
Subject: Re: 3957-VEA TS7720 power outage
I was wondering when you bring it online, what error messages do you see?
There should be some IOS or IEA type messages for the VTS to say whether or
not z/OS is "seeing" it or not.
I do not know about the TS7720 to provide some other options.
But when our OEM VTS has issues, there is a log on the OEM equipment I can
look at and the SYSLOG usually has some messages as well.
Sometimes Ficon gets confused. Varying offline/online sometimes help - but I
am not sure if UCBs or the whole Library needs to come offline/online for your
situation.
Lizette
-----Original Message-----
On Behalf Of Crabtree, Anne D
Sent: Sunday, December 04, 2016 5:58 PM
Subject: 3957-VEA TS7720 power outage
Looking for anyone who know something about a TS7720 to help me! This
machine Is in a hybrid configuration and we had a planned power outage this
morning.
I placed the cluster in service mode and then did a cluster shutdown.
When power was restored, our zBC12 cannot talk to the VTL! We've
tried everything, Hoping someone out there can help. Again, this is a
3957-VEA TS7720 (1.7 release).Our mainframe is a zBC12 and is
physically connected via ficon to this VTL. If this is not enough
information, let me know... I'll do my best to describe the situation.
We do not have a contract with IBM in place at this time and having
been working with hardware support and software support trying to receive
help. In the meantime, any input would be appreciated!
Anne D. Crabtree
System Programmer
WV Office of Technology Data Center
1900 Kanawha Blvd East
Bldg 6, Room B-110
Charleston, WV 25305
(304)957-8292
(304)558-1441 fax
Work Hours: 6AM-2PM EST
----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to ***@listserv.ua.edu with the message: INFO IBM-MAIN