Discussion:
Help with PSF printer.
(too old to reply)
Ward, Mike S
2018-06-05 13:42:14 UTC
Permalink
Raw Message
"-//IPPRTR70 EXEC PGM=APSPPIEP,REGION=6M,TIME=1440,PARM=(,,,,TCPIP)"

All we have a proc that uses the above PSF program and the printdev statements below. I have been looking through all the PSF documentation searching for how to print lower case on that printer. We have lowercase printout that seems to fold to uppercase. The printer is not an FSS printer it's just a plain old IP printer. All printout seems to work fine except that lowercase folds to upper case. I have looked through the pseglib documentation and the fontlib docs, but I can't seem to find anything that tells you how to print lowercase. Can you help out? Just point me to some docs that explains how to do the lowercase. I don't mind researching, I'm just at a loss as to where to look. Any help appreciated.

TIA Mike.



"//PRT70 PRINTDEV FONTDD=*.FONT01, /* FONT LIBRARY DD */
"// OVLYDD=*.OLAY01, /* OVERLAY LIBRARY DD */
"// PSEGDD=*.PSEG01, /* SEGMENT LIBRARY DD */
"// PDEFDD=*.PDEF01, /* PAGEDEF LIBRARY DD */
"// FDEFDD=*.FDEF01, /* FORMDEF LIBRARY DD */
"// JOBHDR=*.JOBHDR, /* JOB HEADER SEPARATOR */
"// JOBTRLR=*.JOBTLR, /* JOB TRAILER SEPARATOR */
"// DSHDR=*.DSHDR, /* DATA SET HEADER */
"// MESSAGE=*.MSGDS, /* MESSAGE DATA SET OUTPUT */
"// PAGEDEF=38511, /* WAS A06462 */
'// FORMDEF=A10111, /* DEVICE FORMDEF DEFAULT */
'// CHARS=(GF15, /* DEVICE @H1C*/
"// GS12), /* DEFAULT FONT SET @H1C*/
"// PIMSG=YES, /* ACCUMULATE DATA SET */
"// DATACK=BLOCK, /* WAS UNBLOCK ON 10/16/13 @H7A*/
"// SETUP=FORMS, /* REPORT ALL DATA-CHECK @H7A*/
"// TRACE=NO, /* BUILD INTERNAL TRACE @H3C*/
"// FAILURE=WCONNECT, /* ACTION ON PRTR FAILURE */
"// TIMEOUT=REDRIVE, /* ACTION ON TIMEOUT */
"// MGMTMODE=OUTAVAIL, /* PRTR MANAGEMENT MODE */
"// CONNINTV=0, /* ADDED 03/22/10 */
"// PORTNO=5001, /* ADDED 03/22/10 */
"// DISCINTV=15, /* DISCONNECT INV IN SECS */
"// IPADDR='172.21.13.101' /* IP ADDRESS */
"//PRT70 ENDCNTL

==========================
This email, and any files transmitted with it, is confidential and intended solely for the use of the individual or entity to which it is addressed. If you have received this email in error, please notify the system manager. This message contains confidential information and is intended only for the individual named. If you are not the named addressee, you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately by e-mail if you have received this message by mistake and delete this e-mail from your system. If you are not the intended recipient, you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited.

----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to ***@listserv.ua.edu with the message: INFO IBM-MAIN
Carmen Vitullo
2018-06-05 13:51:21 UTC
Permalink
Raw Message
You say it's not an FSS printer, so what drives the printer? VPS, CASPOOL LPR, Info print?


Are you using a site specific fontlib?


I think that's where you need to look I have both 240 and 300 pel fontlib's defined for all my printers and have no issues with upper vs lower case .
maybe some printer setting?


Carmen Vitullo

----- Original Message -----

From: "Mike S Ward" <***@SSFCU.ORG>
To: IBM-***@LISTSERV.UA.EDU
Sent: Tuesday, June 5, 2018 8:42:04 AM
Subject: Help with PSF printer.

"-//IPPRTR70 EXEC PGM=APSPPIEP,REGION=6M,TIME=1440,PARM=(,,,,TCPIP)"

All we have a proc that uses the above PSF program and the printdev statements below. I have been looking through all the PSF documentation searching for how to print lower case on that printer. We have lowercase printout that seems to fold to uppercase. The printer is not an FSS printer it's just a plain old IP printer. All printout seems to work fine except that lowercase folds to upper case. I have looked through the pseglib documentation and the fontlib docs, but I can't seem to find anything that tells you how to print lowercase. Can you help out? Just point me to some docs that explains how to do the lowercase. I don't mind researching, I'm just at a loss as to where to look. Any help appreciated.

TIA Mike.



"//PRT70 PRINTDEV FONTDD=*.FONT01, /* FONT LIBRARY DD */
"// OVLYDD=*.OLAY01, /* OVERLAY LIBRARY DD */
"// PSEGDD=*.PSEG01, /* SEGMENT LIBRARY DD */
"// PDEFDD=*.PDEF01, /* PAGEDEF LIBRARY DD */
"// FDEFDD=*.FDEF01, /* FORMDEF LIBRARY DD */
"// JOBHDR=*.JOBHDR, /* JOB HEADER SEPARATOR */
"// JOBTRLR=*.JOBTLR, /* JOB TRAILER SEPARATOR */
"// DSHDR=*.DSHDR, /* DATA SET HEADER */
"// MESSAGE=*.MSGDS, /* MESSAGE DATA SET OUTPUT */
"// PAGEDEF=38511, /* WAS A06462 */
'// FORMDEF=A10111, /* DEVICE FORMDEF DEFAULT */
'// CHARS=(GF15, /* DEVICE @H1C*/
"// GS12), /* DEFAULT FONT SET @H1C*/
"// PIMSG=YES, /* ACCUMULATE DATA SET */
"// DATACK=BLOCK, /* WAS UNBLOCK ON 10/16/13 @H7A*/
"// SETUP=FORMS, /* REPORT ALL DATA-CHECK @H7A*/
"// TRACE=NO, /* BUILD INTERNAL TRACE @H3C*/
"// FAILURE=WCONNECT, /* ACTION ON PRTR FAILURE */
"// TIMEOUT=REDRIVE, /* ACTION ON TIMEOUT */
"// MGMTMODE=OUTAVAIL, /* PRTR MANAGEMENT MODE */
"// CONNINTV=0, /* ADDED 03/22/10 */
"// PORTNO=5001, /* ADDED 03/22/10 */
"// DISCINTV=15, /* DISCONNECT INV IN SECS */
"// IPADDR='172.21.13.101' /* IP ADDRESS */
"//PRT70 ENDCNTL

==========================
This email, and any files transmitted with it, is confidential and intended solely for the use of the individual or entity to which it is addressed. If you have received this email in error, please notify the system manager. This message contains confidential information and is intended only for the individual named. If you are not the named addressee, you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately by e-mail if you have received this message by mistake and delete this e-mail from your system. If you are not the intended recipient, you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited.

----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to ***@listserv.ua.edu with the message: INFO IBM-MAIN


----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to ***@listserv.ua.edu with the message: INFO IBM-MAIN
Rugen, Len
2018-06-05 13:54:02 UTC
Permalink
Raw Message
I think GF15 if "folded", so if the 15 point font is upper cast, try changing that to GT15.

-----Original Message-----
From: IBM Mainframe Discussion List <IBM-***@LISTSERV.UA.EDU> On Behalf Of Ward, Mike S
Sent: Tuesday, June 5, 2018 8:42 AM
To: IBM-***@LISTSERV.UA.EDU
Subject: Help with PSF printer.

"-//IPPRTR70 EXEC PGM=APSPPIEP,REGION=6M,TIME=1440,PARM=(,,,,TCPIP)"

All we have a proc that uses the above PSF program and the printdev statements below. I have been looking through all the PSF documentation searching for how to print lower case on that printer. We have lowercase printout that seems to fold to uppercase. The printer is not an FSS printer it's just a plain old IP printer. All printout seems to work fine except that lowercase folds to upper case. I have looked through the pseglib documentation and the fontlib docs, but I can't seem to find anything that tells you how to print lowercase. Can you help out? Just point me to some docs that explains how to do the lowercase. I don't mind researching, I'm just at a loss as to where to look. Any help appreciated.

TIA Mike.



"//PRT70 PRINTDEV FONTDD=*.FONT01, /* FONT LIBRARY DD */
"// OVLYDD=*.OLAY01, /* OVERLAY LIBRARY DD */
"// PSEGDD=*.PSEG01, /* SEGMENT LIBRARY DD */
"// PDEFDD=*.PDEF01, /* PAGEDEF LIBRARY DD */
"// FDEFDD=*.FDEF01, /* FORMDEF LIBRARY DD */
"// JOBHDR=*.JOBHDR, /* JOB HEADER SEPARATOR */
"// JOBTRLR=*.JOBTLR, /* JOB TRAILER SEPARATOR */
"// DSHDR=*.DSHDR, /* DATA SET HEADER */
"// MESSAGE=*.MSGDS, /* MESSAGE DATA SET OUTPUT */
"// PAGEDEF=38511, /* WAS A06462 */
'// FORMDEF=A10111, /* DEVICE FORMDEF DEFAULT */
'// CHARS=(GF15, /* DEVICE @H1C*/
"// GS12), /* DEFAULT FONT SET @H1C*/
"// PIMSG=YES, /* ACCUMULATE DATA SET */
"// DATACK=BLOCK, /* WAS UNBLOCK ON 10/16/13 @H7A*/
"// SETUP=FORMS, /* REPORT ALL DATA-CHECK @H7A*/
"// TRACE=NO, /* BUILD INTERNAL TRACE @H3C*/
"// FAILURE=WCONNECT, /* ACTION ON PRTR FAILURE */
"// TIMEOUT=REDRIVE, /* ACTION ON TIMEOUT */
"// MGMTMODE=OUTAVAIL, /* PRTR MANAGEMENT MODE */
"// CONNINTV=0, /* ADDED 03/22/10 */
"// PORTNO=5001, /* ADDED 03/22/10 */
"// DISCINTV=15, /* DISCONNECT INV IN SECS */
"// IPADDR='172.21.13.101' /* IP ADDRESS */
"//PRT70 ENDCNTL

==========================
This email, and any files transmitted with it, is confidential and intended solely for the use of the individual or entity to which it is addressed. If you have received this email in error, please notify the system manager. This message contains confidential information and is intended only for the individual named. If you are not the named addressee, you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately by e-mail if you have received this message by mistake and delete this e-mail from your system. If you are not the intended recipient, you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited.

----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions, send email to ***@listserv.ua.edu with the message: INFO IBM-MAIN

----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to ***@listserv.ua.edu with the message: INFO IBM-MAIN
Carmen Vitullo
2018-06-05 14:04:02 UTC
Permalink
Raw Message
Good point! all my default Chars are GTxx


Carmen Vitullo

----- Original Message -----

From: "Len Rugen" <***@MISSOURI.EDU>
To: IBM-***@LISTSERV.UA.EDU
Sent: Tuesday, June 5, 2018 8:53:34 AM
Subject: Re: Help with PSF printer.

I think GF15 if "folded", so if the 15 point font is upper cast, try changing that to GT15.

-----Original Message-----
From: IBM Mainframe Discussion List <IBM-***@LISTSERV.UA.EDU> On Behalf Of Ward, Mike S
Sent: Tuesday, June 5, 2018 8:42 AM
To: IBM-***@LISTSERV.UA.EDU
Subject: Help with PSF printer.

"-//IPPRTR70 EXEC PGM=APSPPIEP,REGION=6M,TIME=1440,PARM=(,,,,TCPIP)"

All we have a proc that uses the above PSF program and the printdev statements below. I have been looking through all the PSF documentation searching for how to print lower case on that printer. We have lowercase printout that seems to fold to uppercase. The printer is not an FSS printer it's just a plain old IP printer. All printout seems to work fine except that lowercase folds to upper case. I have looked through the pseglib documentation and the fontlib docs, but I can't seem to find anything that tells you how to print lowercase. Can you help out? Just point me to some docs that explains how to do the lowercase. I don't mind researching, I'm just at a loss as to where to look. Any help appreciated.

TIA Mike.



"//PRT70 PRINTDEV FONTDD=*.FONT01, /* FONT LIBRARY DD */
"// OVLYDD=*.OLAY01, /* OVERLAY LIBRARY DD */
"// PSEGDD=*.PSEG01, /* SEGMENT LIBRARY DD */
"// PDEFDD=*.PDEF01, /* PAGEDEF LIBRARY DD */
"// FDEFDD=*.FDEF01, /* FORMDEF LIBRARY DD */
"// JOBHDR=*.JOBHDR, /* JOB HEADER SEPARATOR */
"// JOBTRLR=*.JOBTLR, /* JOB TRAILER SEPARATOR */
"// DSHDR=*.DSHDR, /* DATA SET HEADER */
"// MESSAGE=*.MSGDS, /* MESSAGE DATA SET OUTPUT */
"// PAGEDEF=38511, /* WAS A06462 */
'// FORMDEF=A10111, /* DEVICE FORMDEF DEFAULT */
'// CHARS=(GF15, /* DEVICE @H1C*/
"// GS12), /* DEFAULT FONT SET @H1C*/
"// PIMSG=YES, /* ACCUMULATE DATA SET */
"// DATACK=BLOCK, /* WAS UNBLOCK ON 10/16/13 @H7A*/
"// SETUP=FORMS, /* REPORT ALL DATA-CHECK @H7A*/
"// TRACE=NO, /* BUILD INTERNAL TRACE @H3C*/
"// FAILURE=WCONNECT, /* ACTION ON PRTR FAILURE */
"// TIMEOUT=REDRIVE, /* ACTION ON TIMEOUT */
"// MGMTMODE=OUTAVAIL, /* PRTR MANAGEMENT MODE */
"// CONNINTV=0, /* ADDED 03/22/10 */
"// PORTNO=5001, /* ADDED 03/22/10 */
"// DISCINTV=15, /* DISCONNECT INV IN SECS */
"// IPADDR='172.21.13.101' /* IP ADDRESS */
"//PRT70 ENDCNTL

==========================
This email, and any files transmitted with it, is confidential and intended solely for the use of the individual or entity to which it is addressed. If you have received this email in error, please notify the system manager. This message contains confidential information and is intended only for the individual named. If you are not the named addressee, you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately by e-mail if you have received this message by mistake and delete this e-mail from your system. If you are not the intended recipient, you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited.

----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions, send email to ***@listserv.ua.edu with the message: INFO IBM-MAIN

----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to ***@listserv.ua.edu with the message: INFO IBM-MAIN


----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to ***@listserv.ua.edu with the message: INFO IBM-MAIN
Ward, Mike S
2018-06-05 14:10:41 UTC
Permalink
Raw Message
I will try that. Thank you.

-----Original Message-----
From: IBM Mainframe Discussion List <IBM-***@LISTSERV.UA.EDU> On Behalf Of Rugen, Len
Sent: Tuesday, June 05, 2018 8:54 AM
To: IBM-***@LISTSERV.UA.EDU
Subject: Re: Help with PSF printer.

I think GF15 if "folded", so if the 15 point font is upper cast, try changing that to GT15.

-----Original Message-----
From: IBM Mainframe Discussion List <IBM-***@LISTSERV.UA.EDU> On Behalf Of Ward, Mike S
Sent: Tuesday, June 5, 2018 8:42 AM
To: IBM-***@LISTSERV.UA.EDU
Subject: Help with PSF printer.

"-//IPPRTR70 EXEC PGM=APSPPIEP,REGION=6M,TIME=1440,PARM=(,,,,TCPIP)"

All we have a proc that uses the above PSF program and the printdev statements below. I have been looking through all the PSF documentation searching for how to print lower case on that printer. We have lowercase printout that seems to fold to uppercase. The printer is not an FSS printer it's just a plain old IP printer. All printout seems to work fine except that lowercase folds to upper case. I have looked through the pseglib documentation and the fontlib docs, but I can't seem to find anything that tells you how to print lowercase. Can you help out? Just point me to some docs that explains how to do the lowercase. I don't mind researching, I'm just at a loss as to where to look. Any help appreciated.

TIA Mike.



"//PRT70 PRINTDEV FONTDD=*.FONT01, /* FONT LIBRARY DD */
"// OVLYDD=*.OLAY01, /* OVERLAY LIBRARY DD */
"// PSEGDD=*.PSEG01, /* SEGMENT LIBRARY DD */
"// PDEFDD=*.PDEF01, /* PAGEDEF LIBRARY DD */
"// FDEFDD=*.FDEF01, /* FORMDEF LIBRARY DD */
"// JOBHDR=*.JOBHDR, /* JOB HEADER SEPARATOR */
"// JOBTRLR=*.JOBTLR, /* JOB TRAILER SEPARATOR */
"// DSHDR=*.DSHDR, /* DATA SET HEADER */
"// MESSAGE=*.MSGDS, /* MESSAGE DATA SET OUTPUT */
"// PAGEDEF=38511, /* WAS A06462 */
'// FORMDEF=A10111, /* DEVICE FORMDEF DEFAULT */
'// CHARS=(GF15, /* DEVICE @H1C*/
"// GS12), /* DEFAULT FONT SET @H1C*/
"// PIMSG=YES, /* ACCUMULATE DATA SET */
"// DATACK=BLOCK, /* WAS UNBLOCK ON 10/16/13 @H7A*/
"// SETUP=FORMS, /* REPORT ALL DATA-CHECK @H7A*/
"// TRACE=NO, /* BUILD INTERNAL TRACE @H3C*/
"// FAILURE=WCONNECT, /* ACTION ON PRTR FAILURE */
"// TIMEOUT=REDRIVE, /* ACTION ON TIMEOUT */
"// MGMTMODE=OUTAVAIL, /* PRTR MANAGEMENT MODE */
"// CONNINTV=0, /* ADDED 03/22/10 */
"// PORTNO=5001, /* ADDED 03/22/10 */
"// DISCINTV=15, /* DISCONNECT INV IN SECS */
"// IPADDR='172.21.13.101' /* IP ADDRESS */
"//PRT70 ENDCNTL

==========================
This email, and any files transmitted with it, is confidential and intended solely for the use of the individual or entity to which it is addressed. If you have received this email in error, please notify the system manager. This message contains confidential information and is intended only for the individual named. If you are not the named addressee, you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately by e-mail if you have received this message by mistake and delete this e-mail from your system. If you are not the intended recipient, you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited.

----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions, send email to ***@listserv.ua.edu with the message: INFO IBM-MAIN

----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions, send email to ***@listserv.ua.edu with the message: INFO IBM-MAIN

==========================
This email, and any files transmitted with it, is confidential and intended solely for the use of the individual or entity to which it is addressed. If you have received this email in error, please notify the system manager. This message contains confidential information and is intended only for the individual named. If you are not the named addressee, you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately by e-mail if you have received this message by mistake and delete this e-mail from your system. If you are not the intended recipient, you are notified that disclosing, copying, distributing or taking any action in reliance on the contents of this information is strictly prohibited.

----------------------------------------------------------------------
For IBM-MAIN subscribe / signoff / archive access instructions,
send email to ***@listserv.ua.edu with the message: INFO IBM-MAIN
Loading...